The “DL” Tonic 23 (dériveur lesté, ballasted centreboard) has a cast ballast stub under the hull and a pivoting board that retracts into it. One owner gives the draught as 0.70 m with the board up and 1.38 m with it down, with an unballasted board (guy07800, Hisse-et-Oh, 24 June 2012).
How the pivot is built
- A post from 1 January 2009 (user name not shown) shows a photo of the pivot on a DL: one axle runs through the ballast, held by two plates on each side of the ballast, with two pins at each end.
- Tonix23 (27 November 2017) measured it after getting documentation from Jeanneau’s yard at Les Herbiers. The axle is not visible on the stub. It sits 200 mm above the hull and 580 mm back from the leading edge of the stub, in a recess filled with resin. His drawing is in the thread.
- On the inside, the lifting line runs through a fibreglass tube to a winch. A Tonic owner who found water in that tube was told it is normal for the water to stand at waterline level (MartyB, Jeanneau Owners forum, 20 August 2015).
The board jams in the case
This is the most common complaint. Causes owners named:
- Mud. Groundings in muddy areas leave silt in the case that dries hard, especially when the boat sits unused. One reply (28 December 2008, user name not shown) suggested a high-pressure jet from the top of the case. Another owner, who also sails from Audenge (30 December 2008), says he does not raise the board fully, so it knocks with each tide.
- Rust. vrobert78 (9 August 2019) had a board that had swollen with rust and was stuck in the case. He treated it with epoxy and has had no trouble since. On Zeilersforum, Yellow Boat (13 March 2018) gave his view on a stuck board in a Tonic for sale: it is almost certainly rust, because a steel board in a steel stub seizes after years, particularly as few owners take it out and recoat the inside every few years.
- Seized axle. tonic56 (26 January 2010) could not drive the axle out of the ballast, even with hard hammering, and did his repair without removing the board.
- Too tight a fit after a replacement. ecl, who fitted a new board, did not grind enough off the trailing edge. It now jams in the keel if he winches it up tight (Jeanneau Owners forum, 20 August 2015). His tip: raise the board once, mark the line where it meets the winch, and stop at that mark.
- Bent board. martinw (Zeilersforum, 13 March 2018) once ran an old Randmeer onto hard sand under heel; its board bent like a hoop and had to be replaced, which was expensive. fransb (13 March 2018) thought a board of the Tonic type is hard to bend, because it swings up on a shoal. camus (Hisse-et-Oh, 28 May 2019) reported a Tonic board bent to 90 degrees under the boat; it was a rented boat and he did not know how it happened.
Demian12 added a tip in the same thread as the 2008 posts (2 October 2017, boat type not given): he stopped the sticking by leaving a little board down, and once freed a stuck board by motoring into waves with some slack in the line.
One Zeilersforum member, who said he did not know the Tonic, advised that on boats with a lifting keel or board the lifting mechanism is often a weak link and worth checking before buying (roblisto, 5 September 2017).
In the Zeilersforum thread, a buyer (Apollo, 24 March 2018) found his board stuck in peat and shells; after the boat was hauled out and rinsed, it turned freely. He also found pits about 2 cm wide in the board, and the forum disagreed on the cause. Have a yard look at pitting like that.
Replacing the board
- Gilletarom (2 July 2019) suggests having a metal workshop copy the old board: lift the boat, lower the board, trace the outline on paper, measure the thickness and the axle hole.
- Kerhulcoq (26 June and 2 July 2019) wanted to replace his original board with a stainless one, swapped in one lift. aaledo (28 October 2019) asked for plans, and Gildas29 replied that he had overhauled the whole mechanism on his Tonic and sent him a drawing the next day.
- jfgege (14 May 2021) reported a board riddled with holes and had the dimensions but not the weight. The only reply, from patbzh (15 May 2021), points to a Facebook page for the Tonic.
- Gildas29 (8 July 2016) asked for a detailed plan of the board and said his knocks loudly in the case although it seems to have no play.
- fedalaAntibes (27 February 2015) asked for a plan of a retractable board; the thread title says the keel “left at sea”. No details were given.
- In May 2026, lulu937 asked whether a stuck board can be freed from above through a hatch in the saloon table. The thread had no answer when saved.
Treating the stub
Picadou (Hisse-et-Oh, 9 March 2018) asked what to use on the ballast stub of his Tonic 23, which was starting to pit. fritz the cat answered the same day: a rust converter (Ferose), then an epoxy primer and antifouling, with filling and stripping first if needed.
If the lifting line breaks
After a poster (Nautal, 22 July 2021) broke his lifting cable, earendil (23 July 2021, writing about a Kelt 707, a different boat) warned against letting a boat dry out with a free-hanging board, because of the risk to the case and the axle. His advice: strap the board up with a line round the hull until the cable is replaced, and lower it again to change the cable. For drying out a Tonic see the article on beaching legs.
Have the board, axle and stub checked by a yard before you rely on them, and especially before you replace the board.
Sources
- Hisse-et-Oh, “Dérive bloquée” (in French): original poster and replies dated 28 and 30 December 2008, post of 1 January 2009, Tonix23 (27 November 2017), Demian12 (2 October 2017).
- Hisse-et-Oh, “Dérive Tonic 23“: kikabarjot (24 January 2010), tonic56 (26 January 2010), Gildas29 and aaledo (2015, 2019).
- Hisse-et-Oh, “Dérive inox Tonic 23“: Kerhulcoq (1 July 2019), Gilletarom (2 July 2019), aaledo and Gildas29 (28 to 30 October 2019).
- Hisse-et-Oh, “urgent [dérive à refaire]“: camus (28 May 2019).
- Hisse-et-Oh, “TONIC 23“: Gildas29 (8 July 2016).
- Hisse-et-Oh, “traitement / peinture lest de mon Tonic 23“: Picadou and fritz the cat (9 March 2018).
- Hisse-et-Oh, “TONIC 23“: vrobert78 (9 August 2019).
- Hisse-et-Oh, “TONIC 23 recherche plan de la quille relevable qui est partie en mer“: fedalaAntibes and others (2015), jfgege (14 May 2021).
- Hisse-et-Oh, “Le Tonic 23 est il un (le meilleur) choix dans mon cas“: lulu937 (19 May 2026).
- Hisse-et-Oh, “Tonic 23 : Vous en pensez quoi?“: guy07800 (24 June 2012), draft figures.
- Jeanneau Owners Network Forum, “Owners Manual Tonic 23“: frankieboy59, MartyB, ecl (12 to 20 August 2015). The live page is behind a bot check; the text was read in a Wayback Machine copy.
- Zeilersforum.nl, “Klapzwaard Jeanneau Tonic zit vast“: Apollo, marcs, Yellow Boat, martinw (11 to 26 March 2018).
- Zeilersforum.nl, “Jeanneau Tonic 23; waar moet ik op letten?“: roblisto (5 September 2017).