Knowledge

Keel & hull

Beaching legs and drying out

The centreboard Tonic is often grounded on legs fixed to the chainplates. Owners explain how to set them, what went wrong, and why the fin-keel version needs more care.

Last updated October 23, 2026

Which version can dry out

  • Centreboard (DL). The keel stub under the hull carries the boat (vrobert78: it should rest mainly on the keel), and the legs keep it upright. tribu, who skippered a school DL on the south Brittany coast in 1995 and 1996, grounded it at Sauzon (Belle-Île) using the two legs for balance (Hisse-et-Oh, 24 January 2015).
  • Fin keel. The asker of the thread gives its draught as 1.10 m. juliusse (10 October 2019), who only knows the DL, was tempted to say occasional legs are possible, depending on the shape of the keel. Kerhulcoq (10 October 2019) is cautious: stability is not a given, so check that the floor timbers (varangues) can take the weight, and put the legs in the right place. For regular beaching he recommends the DL. Nobody in the thread reported grounding a fin-keel boat.
  • Opinions differ on how good the DL is for this. jerom-826 (9 August 2019) calls the DL the worst solution, because it performs worse than a fin keel and cannot be grounded without legs. golfhotel (19 August 2019) chose it anyway for short trips in quiet places, where the stub protects the hull when grounding.

The legs

  • The standard legs are Jeanneau’s galvanised telescopic legs, which bolt onto the chainplates at deck level. They were also fitted to the Fantasia, and boats of the Sun 2500 type are a place to look at the layout (penloch, 16 November 2018). Fantasias or Sun 2500s stored ashore at yards often still have them.
  • vendesir2 (17 November 2018) offered the upper parts of a set for a few euros and gave dimensions: overall length 1 m, intermediate leg at 55 cm, fixing foot 5 cm, outside diameter 6 cm. One leg lacked its intermediate piece and one had been welded the wrong way round. Capucin (same day) says the hardest part to make is the piece that fits the chainplate.
  • penloch (20 November 2018) says aluminium legs are hardly lighter than steel ones at equal strength; for the lower part he used stainless steel.
  • penloch (17 November 2018) says that with repeated groundings the load on the chainplate soon causes play and leaks in the cabin, so fit backing plates of good size inside. See the chainplates article.

Setting the legs and grounding

  • One owner keeps the legs short. vrobert78 (15 July 2018) sets his at the minimum, so the boat rests mainly on its keel, with only one of the two legs really taking load. He says the first time he did not do this, it cost him a trip to the yard for a proper repair. Gildas29 (16 July 2018) agreed.
  • vrobert78 (9 August 2019) had trouble on his first groundings because he had left too much length on the legs.
  • He says he drops a stern anchor so the boat stays in line with the beach, and is always on hand to check as the boat settles.
  • He finds the awkward part is emptying the big locker (his holds the inflatable dinghy and its engine) to get at the legs in a small cockpit.
  • He reports no problem with mud and the board; they grounded at Bréhat that summer.

Hull support ashore

Other advice on supporting the hull on a trailer and for the winter is in the trailer article. The hull is thin: JLPIER (Hisse-et-Oh, 8 March 2022) was surprised by how thin it was when he changed the through-hulls.

Legs, chainplates and the structure under them carry the weight of the boat. Have a yard check the arrangement on your boat before you ground it for the first time.

Sources